Sensor ea ho Lekanya Sebaka sa Laser ea 'Mele oa PDB-CC50TGI 4 ho isa ho 20mA
Sensor ea laser ea moralo oa CMOS ea maemo a holimo e loketse ho lekanya libaka. Mohloli oa leseli la laser o se nang kotsi ho lekanya lintho tse nyane haholo ka nepo. Algorithm e ntle e fihlella ho lemoha ho nepahetseng le litekanyo tse tsitsitseng, tsa mosebetsi ofe kapa ofe, tlhahlobo ea ho kenya tiiso ea li-bearing e nyane le ea ho bokella li-chip kapa kahlolo e fosahetseng. Ka ponts'o ea dijithale ea OLED, ho bonolo haholo ho e bala le ho e sebelisa. Mesebetsi e mengata e hahiloeng kahare e ka khotsofatsa litlhoko tse fapaneng tsa ts'ebeliso ka botlalo.
> Ho lemoha tekanyo ea ho falla
> Sebaka sa ho lekanya: 80...500mm
> Boholo ba ntlo: 65*51*23mm
> Sebaka se khanyang: Φ2.5mm@500mm
> Matla a tshebediso: ≤700mW
> Qeto: 15um@80mm:500um@500mm
> Sehlahiswa: RS-485 (Tšehetso ea Modbus protocol); 4...20mA (Khanyetso ea mojaro ＜390Ω)/PUSH-PULL/NPN/PNP 'me NO/NC Settable
> Mocheso o tloaelehileng: -10…+50℃
> Thepa ea Bolulo: Bolulo: ABS; Sekoahelo sa lense: PMMA
> Tšireletso e felletseng ea potoloho: Potoloho e khutšoanyane, polarity e khutlelang morao, tšireletso ea ho jara boima bo feteletseng
> Tekanyo ea tšireletso: IP67
> Leseli le thibelang tikoloho: Leseli le hlabang: ＜3,000lux
> Li-sensor li na le likhoele tse sirelelitsoeng, terata Q ke sesebelisoa sa ho bulela.
| Matlo a polasetiki | ||
| E tloaelehileng | ||
| RS485 | PDB-CC50DGR | |
| 4...20mA | PDB-CC50TGI | |
| Litlhaloso tsa tekheniki | ||
| Mofuta oa ho lemoha | Tekanyo ea sebaka | |
| Sebaka sa ho lekanya | 80...500mm | |
| Sekala se felletseng (FS) | 420mm | |
| Phepelo ea motlakase | RS-485:10...30VDC;4...20mA:12...24VDC | |
| Matla a tšebeliso | ≤700mW | |
| Mojaro oa hona joale | 200mA | |
| Ho theoha ha motlakase | <2.5V | |
| Mohloli oa leseli | Lese e khubelu (650nm); Boemo ba laser: Sehlopha sa 2 | |
| Sebaka se khanyang | Φ2.5mm@500mm | |
| Qeto | 15um@80mm:500um@500mm | |
| Ho nepahala ha mola | RS-485:±0.3%FS;4...20mA:±0.4%FS | |
| Ho nepahala ho pheta-pheta | 30um@80mm;250um@250mm; 1000um@500mm | |
| Sehlahisoa sa 1 | RS-485 (Tšehetso ea Modbus protocol); 4...20mA (Khanyetso ea mojaro ＜390Ω) | |
| Sehlahisoa sa 2 | PUSH-HULL/NPN/PNP 'me NO/NC e ka hlophisoa | |
| Sebaka se behiloeng | RS-485:Setlhophiso sa ho tobetsa konopo/RS-485; 4...20mA:Setlhophiso sa ho tobetsa konopo | |
| Nako ea karabelo | 2ms/16ms/40ms E ka hlophisoa | |
| Litekanyo | 65*51*23mm | |
| Pontšo | Pontšo ea OLED (boholo: 14 * 10.7mm) | |
| Ho thella ha mocheso | ± 0.02%FS/℃ | |
| Sesupo | Sesupo sa matla: LED e tala; Sesupo sa ketso: LED e mosehla; Sesupo sa alamo: LED e mosehla | |
| Potoloho ea tšireletso | Potoloho e khutšoanyane, polarity e khutlelang morao, tšireletso ea ho jara boima bo feteletseng | |
| Mosebetsi o kentsweng kahare | Setaele sa Aterese ea Lekhoba le Sekhahla sa Kou; Potso ea liparamente; Tlhahlobo ea sehlahisoa; Setaele sa tlhahiso; Setaele se tloaelehileng; Thuto ea ntlha e le 'ngoe; Ruta fensetere; Khutlisa litlhophiso tsa fektheri | |
| Tikoloho ea litšebeletso | Mocheso oa ts'ebetso: -10…+50℃; Mocheso oa polokelo: -20…+70℃ | |
| Mocheso o tloaelehileng | 35...85%RH(Ha ho na condensation) | |
| Leseli le thibelang tikoloho | Leseli la incandescent: ＜3,000lux | |
| Tekanyo ea tšireletso | IP67 | |
| Thepa | Matlo: ABS; Sekoahelo sa lense: PMMA | |
| Khanyetso ea ho thothomela | 10...55Hz Bophahamo bo habeli 1mm, 2H ka 'ngoe ka litsela tsa X, Y, Z | |
| Khanyetso ea tšusumetso | 500m/s²(Hoo e ka bang 50G) makhetlo a 3 ka 'ngoe ka litsela tsa X, Y, Z | |
| Mofuta oa khokahano | Thapo ea RS-485:2m ea li-pin tse 5 tsa PVC;4...20mA:2m Thapo ea PVC ea lipin tse 4 | |
| Sesebelisoa | Sekuru (M4×35mm)×2、Nat×2、Washer×2、Sebakete sa ho kenya、Buka ya tshebetso | |
ZX1-LD300A81 Omron
